Additionally, special care should be taken to prevent problems with wheel support and environmental conditions for wheels stored in mobile storage areas, such as:
- (a) Rescue Squad trucks
- (b) Field contractors
- (c) Barges and boats
Abrasive wheel storage racks should be designed, constructed, and located to fit the user’s needs. The following factors should be considered:
Location
All abrasive wheels should be stored in a dry area in rooms not subject to extreme temperature changes since some bonds may be affected by excessive humidity, dampness, and extreme temperature differentials. Racks should be located as near as practical to the grinding location, but never where there is a danger of damage from passing trucks, crane handling, or excessive vibration.
Storage Methods
The racks, bins, or drawers should be constructed so that each of the various types of wheels can be stored in an orderly and safe manner. Wheel selection should be possible with a minimum of handling. The choice of racks, bins, boxes, or drawers for storage depends on the size and type of wheels. The following suggestions should be considered.
- Thin organic bonded wheels, such as those used for cutting off, should be laid flat on a flat steel surface or similarly rigid material away from excessive heat, moisture, and other liquids to prevent warpage. Loose blotters should not be placed between stacked thin wheels. If thin wheels are supplied with blotters attached, suitable separators should be used to preserve flatness.
- Large diameter wheels (Types 1, 5, 7, 20, 21, 22, 23, 24, 25, and 26) of appreciable thickness are best supported in racks. The racks should provide cushioned two-point cradle support to prevent the wheels from rolling. Partitions help facilitate wheel selection with a minimum of handling.
- Flaring cup wheels (Type 11) are best stored, as illustrated in Figure 1, to prevent chipping of edges.
- Small wheels (approximately 4 inches or less in diameter), except flaring cup wheels (Type 11), are often stored in boxes, bins, or drawers.
- Blotters supplied loose should be stored flat.
- Copies of all safety folders and notices should be prominently displayed in the storage area and available to the machine operator.
Abrasive wheels must be protected while awaiting use. Wheel storage should be arranged to allow for the removal of wheels without disturbing or damaging other wheels. Storage and records should also be set up to allow for wheel use on a rotational basis so that wheels will be in storage for a minimum length of time. This minimizes the possibility of damage from lengthy storage. Such suitable storage should be available for partly used and new wheels.
In addition to the aforementioned ANSI storage requirements, abrasive wheel storage after being mounted on portable machines must also be considered. Abrasive wheels must be removed from the portable grinder during overnight storage and while moving the machine and wheel from one worksite location to another.
Care must also be used during the regular work shift during short-term storage, such as placing the machine down to do other tasks (i.e., welding, etc.) A wheel/machine storage rack or other means of protecting the wheel/machine must be employed. NEVER allow the wheel/machine to drop onto the floor or toss it. Impacts from such abuses can damage the wheel, which may result in wheel breakage. Never leave the wheel/machine anyplace where the wheel or machine may become damaged. When you restart the machine, you may return to find a potentially dangerous situation.
Proper grinding wheel handling and storage is of the utmost importance, and many wheel breakages can be traced back to improper handling and wheel storage. Remember, the life you save may be your own and your coworkers!
For additional information on this topic or if you need any other abrasive safety information, please review the Norton Product Safety page, “best if used by” information, ANSI, OSHA and all literature provided by the abrasive wheel and machine manufacturer. You may contact the Saint-Gobain Product Safety Department at (508) 795-2317, fax: (508) 795-5120, or contact your Saint-Gobain Abrasives representative with any safety related questions.
Related Articles
Safety
Better Safety Equals Better Profitability: Masonry Saw Safety
Focused on making masonry work safer, Norton recently published this article on best practices for m...
Better Safety Equals Better Profitability: Masonry Saw Safety
Safety
ANSI B7.1 - The Industry Standard for Grinding Wheel Safety
ANSI B7.1 is the industry standard for grinding wheel safety. Learn more about how you can leverage ...
ANSI B7.1 - The Industry Standard for Grinding Wheel Safety
Safety
Flanges: A Critical Link in Grinding Wheel Safety
Flanges are critical to safely operating a grinding wheel. See how to ensure flanges are in good con...
Flanges: A Critical Link in Grinding Wheel Safety
Safety
When is a Grinding Wheel Worn Out?
Review this safety information to find out when you need to replace your grinding wheel.
When is a Grinding Wheel Worn Out?
Safety
Reducing Bushings – Know the Rules
Learn the general rules for using a reducing bushing, as explained in the ANSI B7.1 safety requireme...
Reducing Bushings – Know the Rules
Safety
Coated Abrasive Fiber Disc Safety
Learn how to properly store your coated abrasive fiber discs to avoid cupping and how to safe when u...
Coated Abrasive Fiber Disc Safety
Safety
Use Wheel Guards and Face Shields Together to Prevent Facial Injuries
Why risk possible facial injuries when it can easily be prevented?
Use Wheel Guards and Face Shields Together to Prevent Facial Injuries
Safety
Blotters - A Lasting Impression
Learn how to use blotters to check the state of your flanges based on contact, pressure and movement...
Blotters - A Lasting Impression
Safety
Grinding Machine Maintenance
Learn how to visually inspect and speed check your grinding machines to ensure safe grinding wheel u...
Grinding Machine Maintenance